Joined in 2023 
82 
63 About this deal
To avoid wireless disconnect issue during firmware upgrade process, it's recommended to upload firmware with wired connection unless there is no LAN/Ethernet port on your TP-Link device. Using the Omada SDN Controller to Manage Omada Devices Across Multiple Locations Via a Controller (5.0 and Above) 05-31-2023 20217 meer capaciteit verwijst naar de toename van de gemiddelde doorvoer in omgevingen met een hoge dichtheid in vergelijking tot een standaard 4×4 11ac access point.
Configuration Guide on EAP-TLS authentication for WPA-Enterprise (with FreeRADIUS) 09-27-2022 56017 Zero-Touch Provisioning requires the use of Omada Cloud-Based Controller. Please go to Omada Cloud-Based Controller Product List to find all the models supported by Omada Cloud-Based Controller. Note: The TP-Link EAP660 HD is an AX3600-class wireless access point, which means that the theoretical maximum data transfer rate on the 2.4GHz band is 1,148Mbps, while on the 5GHz, it’s 2,402Mbps – don’t get your hopes up, because you’re not going to see this performance outside lab conditions. Features and Wireless TestThis firmware fully adapts the Omada SDN platform but only compatible with Omada Controller v4.1.5 or above. A firmware update can resolve issues that the previous firmware version may have and improve its current performance. To Upgrade Fixed the bug that the wireless clients which install the Omada APP may disconnect from the 5G radio of EAP if we change the 2.4G channel or Tx power of this EAP in the Omada APP. Using Omada controller to configure multiple SSIDs with different VLANs on TP-Link Omada EAPs and Switches to work with a non-Omada gateway(Multi-Net NAT supported) 07-07-2023 17563
Yes. Requiring the use of OC300, OC200, Omada Cloud-Based Controller, or Omada Software Controller. The case is entirely made of plastic though, so it did needs quite a few openings to let the heat flow outwards (while an alloy body will absorb it faster and perhaps better). Then again, I opened the case and I saw that there is a fair bit of room to allow a proper internal airflow. The case does get warm near the middle of the case, both upwards and downwards, but the EAP660HD did not overheat. Some official firmware of TP-Link products can be replaced by the third party firmware such as DD-WRT. TP-Link is not obligated to provide any maintenance or support for it, and does not guarantee the performance and stability of third party firmware. Damage to the product as a result of using third party firmware will void the product's warranty. Open Source Code For Programmers (GPL)Explanation of portal authentication failure after EAP is extended with Range Extenders 11-22-2021 32633 And then, there’s the BeamForming which focuses the signal towards the compatible client devices, reducing the impact of interference and improving the available bandwidth. But, since most users will want multiple of these devices to work together and form a single network, there is the expected support for the mesh technology.
Omada CBC v5 must use this version of Omada Discovery Utility due to the change of the inform url format. What I wanted to mention is that it seems that the roaming with the aforementioned type of client devices is faster when using the Omada controller, such as the OC200 than simply using the access points without a controller (which is very much possible) – this topic discusses it more in detail. I don’t know if I still have to mention it, but the mesh technology has the ability to self heal in case a node (AP) goes offline and it does automatically optimize itself depending on the number of nodes, the number of clients, the signal strength and more. Before moving forward, I need to mention that the access point does not support 160MHz channel bandwidth, it’s only limited to 80MHz.Optimize the high resources using of Omada Controller when managing a large number of EAPs in batches. Fixed the bug that when a port conflict is detected, the prompt message is not centered and the display is incomplete. If you are using an old Omada controller and plan to upgrade this firmware for EAP, you must upgrade the Omada Controller as well: Upgrade Guide IMPORTANT: To prevent upgrade failures, please read the following before proceeding with the upgrade process The Ubiquity U6 LR access point looks a lot like the EAP660HD. It offers similar performance in terms of bandwidth and has a 4x4 radio system. But like the WAX214, the Ethernet uplink port is limited to only 1Gbps while the single-core CPU is not in the same class as the EAP660HD quad-core. You will get more for your money with a EAP660HD. Final verdict
Great Deal 
New Comment